<dfn id="njcjq"></dfn>
        1. <address id="njcjq"></address>
          1. <address id="njcjq"><font id="njcjq"><strong id="njcjq"></strong></font></address>

                  Focus on environmental protection and devote to pollution prevention

                  Provide reliable and safe product for
                  the electronic industries

                  Technical support

                  6-7 Operation Manual for Flux
                  6-7-1 Preparation:

                  1. Circuit boards and components: In order to maintain a stable welding performance and electrical reliability, circuit boards and components shall meet the solder-ability requirements and ion pollution requirements. Assembly manufacturers are suggested to establish the relevant provisions based on the requirements mentioned above and suppliers may be required to provide analysis reports or incoming inspection.
                  2. Pick-and-place: It is recommended that wearing clean non-woven gloves when picking or placing circuit boards. Please be cautious when contact the circuit boards; only the edge can be touched.
                  3. Cleaning: Conveyor belt, fixtures and trays should be kept clean and can be cleaned with detergent. In the replacement of a flux, it is recommended to use the new foam tubes (have a clean-off).

                  6-7-2 Application:

                  1. For the foam, the foam compressed air devices should be free of water and oil, and maintain full flux, which should be maintained 2 ~ 3cm higher than the foam pipe. Adjust the air pressure to get the best foaming height and foam fineness, and to make it foam at a constant rate to the top.
                  2. For the spray, the uniformity can be estimated with a piece of board (cardboard, glass, etc.) through the spray and preheat areas.
                  3. Solid content control: When used in foam, the diluent should be added to supplement the volatile solvents, to control the flux of the solid content. In continuous production, check whether proportion of solid content is in acceptable range every 2-4 hours.
                  4. Residues and contaminants will accumulate in the repeated use of the flux in long term use. In order to obtain good welding results, replacing
                  flux every one or two days is recommended, as well as cleaning the diluent tank and foam tubes.
                  5. The removal of residues: residue remains after soldering; it can be cleaned with special detergent if necessary.

                  6-7-3 Equipment setting:

                  Operating parameters

                  Reference value

                  Coating volume

                  foam:1000-1800 ug/cm2
                  spray:800-1500 ug/cm2

                  used in foam

                  Foam aperture

                  20-50um

                  Foam tube from the top to the surface flux

                  20-30mm

                  Foam pipe cover openings

                  10-13mm

                  Preheating temperature

                  Board surface

                  80-110℃

                  Plate under the surface

                  35℃

                  On-board increase in maximum speed of the surface (the original device in order to avoid injury)

                  2℃/3.5° F/s

                  Angle conveyors

                  5-8° (6°)

                  Conveyor speed

                  1.1-1.8m/min

                  Tin furnace slurry contact time

                  1.5-3.5min

                  Tin furnace temperature

                  Sn63

                  235-265℃

                  lead-free 

                  258-270℃

                  Note: These are general guidelines and can lead to a good welding performance. However, different equipment, components and circuit boards will require different optimized settings, which require the pilot trials to determine the most important parameters (such as the volume of coating, conveyor speed, tin furnace temperature, preheating temperature).

                  6-7-4 Cautions:
                  1.In filtration and the welding process, avoid direct contact with skin and inhalation of steam. Better wear protective glasses and rubber gloves, masks in operation. If the any object splashes into the eyes in the process, wash the eyes immediately with plenty of water and seek for medical treatment afterwards.
                  2.Fetch the corresponding dose of flux according to the amount of output. Cap the flux liquid container if it’s not being used to protect it for future use; The color of flux may darken after long-time storage, which has no side effect for use.
                  3.Keep good ventilation in workshop or at the operation scene.
                  4.Operation must not be performed in haste. Be cautious in leaching flux and soldering process, in order to avoid flux  splashing or hot liquid spattering.

                  6-7-5 Fire Contral Related Parameters

                  Flash Point(°F):65 Auto Ignition Temperature:460℃
                  Uel Upper(VOL):7.99 Usual Fire Explosion Hazards:N/O
                  Lel loower(VOL):2.02 Extinguisher Media:CO2/Powder Extinguisher
                  津ICP備05011517號-1 Copyright © 2010 Cooper ZhongyaSolder,Inc All Rights
                  亚洲制服丝袜av一区二区三区,亚洲色在线v中文字幕,中文乱码字幕无线观看2019,国产男同